Showing results: 91 - 105 of 162 items found.
-
F56 -
Beijing Airport Beiguang Instruments Co., Ltd
F56 Metal Tube Float Flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
-
Mass Flow -
ATEQ Corp.
At ATEQ, we carry both touch screen and digital mass flow leak testers models. Our products have a simple setup and are easy to operate.Since flow testing is typically used for calibration and leak detection, it is important that you have a reliable, accurate, and user-friendly mass flow air product on hand. Common uses for our mass flow testers include discovering fluid and potential gas leaks, as well as occlusion testing. It is imperative that both objects you test with this type of instrument carry nearly identical reference volumes.
-
C-Series -
MKS Instruments
The C-Series Mass Flow Controller (MFC) is a compact, fast-response model using a Micro-Electro-Mechanical Systems (MEMS) based flow sensor for non-corrosive gas applications. It is available in Full Scale flow rates from 50 sccm to 50 slm (N2 equivalent) with a control range from as low as 0.1% of Full Scale up to 100% of Full Scale and is also available as a flow meter. Analog (0 to 5 VDC) or digital (RS485 or Modbus TCP/IP) communications interfaces are available. Required power supply voltage is 24 VDC nominal.
-
Fuel Cell Technologies, Inc
Mini-Test Station for low current fuel cell testing. The test station includes Analog mass flow controllers for Anode and Cathode gas streams, humidity bottles with preheaters and temperature controllers and a cell temperature controller. The test station is designed to use the customer's Potentiostat to load the cell. Manual backpressure is provided for pressures from 0-60 psig. The Mini-Test station is basically our Analog Mass Flow Controlled Low Flow Humidification System with all the options.
-
TU Series -
HORIBA, Ltd.
The test gas generation systems in the TU Series include a test gas generation system for evaluating the performance of various kinds of gas sensors, as well as systems for generating simulated gases for evaluating catalysts. These systems are personally tailored to customers’ intended uses.Among the systems we offer some utilise multiple mass flow controllers to mobilize functions (e.g. to generate gases of any concentration, to add moisture, to control supplied gas pressure and to heat gases) thereby allowing for comprehensive control via a PC or PLC.A common use of this product within the biotechnology field is as an atmosphere gas supply system inside fermenters.
-
HDPS -
Rhesca Co., Ltd.
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
Teledyne Monitor Labs
From the #1 Leader in flow monitoring technology, TML is proud to offer the Ultraflow 150 and the Deltaflow 180 flow rate monitors. Both monitors measure actual velocity, temperature and pressure to report flow rate at standard conditions. The monitors calibrate daily to validate data accuracy.Both monitors offer a user interface which identify instrument calibrations and faults along with maintenance alerts. All of our monitors are designed to meet the rigorous demands of stack or industrial process gas monitoring.
-
Renesas Electronics Corp.
The rotational flow demonstration kit detects the rotational position using the MCU’s on board data transfer controller (DTC) function, a form of state machine, while the MCU’s core is in stop-mode state. This ensures that the average power consumption is kept as low as possible, with IAV (average current) at 4.5 microampere (μA) and a 32 sample burst per second. The flow demonstration kit senses the flow direction and volumetric flow rate of water and gas, and can also detect reverse flow. The demonstration kit is applied using an active inductive method. Two coils are used to sense the rotational position of a part-metalized disk, and a third coil is used to generate a reference signal.
-
Nelson Acoustics
* Sound Quality: Find our what your end users like or dislike about emitted noise. * Low-Noise Product Design: Apply interinsically-quiet design principles to your device * Fan Noise: move cooling air quietly * Gas Flows: Reduce noise from industrial gas processes * Advanced analysis and signal processing: Finding the relevant "needle" in the "haystack" of data.
-
IMI-FLOW -
Hiden Isochema Ltd
The IMI-FLOW combines the manometric gas sorption capabilities of all IMI analyzers with flowing mode operation and integrated mass spectrometry. Manometric mode offers high accuracy isotherm determination to 200 bar, while the flowing mode provides complete control of pressure, composition and flow rate. Integrated mass spectrometry allows downstream gas analysis for TPD and advanced methods.
-
Chandler Engineering
The variety of models within the Quizix line offers several key advantages. The wide range of flow rates, pressure configurations and available options allow Quizix pumps to meet virtually any experimental requirement from bench top to pilot scale. The ability of Quizix pumps to handle almost any slurry, paste, liquid or gas provides unique capability not found in other positive displacement pumps. Exceptional flow rate accuracy, combined with non-stop pulseless flow makes Quizix pumps ideal for applications involved with rock core analysis/reservoir engineering, oil and gas production enhancement studies, EOR/IOR, PVT, rock mechanics, catalyst or chemical feed stock addition for reactor feed/chemical synthesis and any fluid delivery application where critical fluid delivery or pressure control is required.
-
HFM-200 LFE -
Teledyne OEM Solutions
The HFM-200 LFE Series by Teledyne Hastings can be configured and accurately measure gas flow in a broad array of applications. Featuring reliability and stability, the 200 Series is chosen by users for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow meter compatible with most gases.The HFM-200 LFE meter has flow ranges from 0-10 sccm to flows of 0-15,000 slm; provides analog outputs, and is constructed of stainless steel. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Cleaning for oxygen service is available. Our laminar flow elements (smooth, threaded or flanged) are available in various sizes from 3/8" up to 8". Low pressure drops at full scale flow.
-
HFM-200 LFE -
Teledyne Hastings Instruments
The HFM-200 LFE Series by Teledyne Hastings can be configured and accurately measure gas flow in a broad array of applications. Featuring reliability and stability, the 200 Series is chosen by users for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow meter compatible with most gases.The HFM-200 LFE meter has flow ranges from 0-10 sccm to flows of 0-15,000 slm; provides analog outputs, and is constructed of stainless steel. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Cleaning for oxygen service is available. Our laminar flow elements (smooth, threaded or flanged) are available in various sizes from 3/8" up to 8". Low pressure drops at full scale flow.
-
GAS DISTRIBUTION -
TEK-VAC INDUSTRIES Inc.
Tek-Vac will fabricate equipment subassemblies to customer specifictionsViewed here are two process gas distribution systems including mass flow controllers, isolation valves, and stainless steel manifolding. All fittings are metal sealing and all welds are full penetration.
-
PTFM-1000V2 -
HORIBA, Ltd.
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
